Chemineer HS Turbine Agitators

Chemineer HS Turbine Agitators offer the same ruggedness, dependability and simplicity of design found in our other high-quality turbine agitators and mixers. At the heart of the HS Agitator is a right-angle drive exclusively engineered for side-entering agitator service.

当水箱太大而无法方便地安装顶部搅拌器，或者在严重限制头部空间时，Chemineer®HS侧面输入的涡轮搅拌器有效地工作。在大型水箱上支撑顶部的搅拌器通常比安装侧面搅拌器要贵得多。可以消除极高坦克上的长轴，以节省成本和设计简单性。对于大型坦克装置，几个较小的侧面搅拌器可能比单个较大的单元更有效，更经济。

The HS Agitator is available in four standard sizes from 1 to 75 hp. Special designs, up to 250 hp, are available. The wide range of power selections and seal options, combined with two standard output speeds and accurately sized impellers, means that there is an HS agitator available for nearly every standard application. Consider HS Side-Entering Agitators for process applications involving continuous blending, heat transfer, mass transfer or solids suspension.

Drive Elements

右角设计
The right-angle gear design of the HS Agitator reduces overhung load and minimizes nozzle reinforcement requirements. A structural steel support leg is standard on HS Agitators with optional adjustable tie-rods available.

Spiral Bevel Gearing
HS drives utilize hardened spiral bevel gearing sized to provide heavy-duty performance and strength. All gears are load-rated per AGMA standards and inspected to AGMA Quality 10 levels.

High-Capacity Tapered Roller Bearings
Timken®高容量，整个HS驱动器的锥形滚子轴承至少为30,000 -小时L10轴承寿命，可提供长时间的使用寿命和出色的耐磨性。

Positive Lubrication
All gears and bearings in the HS drive are splash-lubricated by an exclusive system developed by Chemineer. Double lip seals on the drive shaft prevents oil loss or the infiltration of contaminants.

Extra Capacity Reducer Shaft
Due to a large cross-section, the low-speed shaft inside the drive minimizes gear misalignment and deflection. The extension shaft is also designed to minimize deflection for superior seal life. Shafts are stocked in carbon steel as well as types 304 and 316 stainless steel. Machinable alloys are also available to address an even wider array of applications.

运动类型和安装
为了安装灵活性和易于安装，HS搅拌器与标准的脚部电动机兼容，范围为1至75 hp。即使将搅拌器安装在水箱上，垂直调节螺钉也可以精确地对齐电动机。随时可用，标准耦合减少了成本和替代困难。

Rugged Steel Construction
Drive housings, support pedestals and mounting feet are fabricated from steel plate using high-tech NC machining equipment. Each component must then pass a quality inspection on a computerized precision coordinate measuring inspection machine. Each housing features lifting lugs and eyebolts for simplified, safe handling of the agitator during installation and removal. Catalyzed, polyurethane exterior finishes protect against corrosion in both indoor and outdoor operating environments.

坦克关闭系统
在所有HS搅拌器上，缩回的机制和密封关闭是标准配置。这允许更换墨盒机械密封或重新包装填充盒，而无需清空水箱。

The mechanical seal shut-off is engaged when the easily accessible retraction bolt pulls the shaft shut-off collar back into the flange housing. The shut-off seal is provided by a fluoroelastomer O-ring. The shaft is then rotated to lock the extension shaft into the housing. This locking feature assures positive shut-off and shaft stability during a mechanical seal change.

The stuffing box shut-off is accomplished by simply tightening the retraction bolt which pulls the shut-off collar back and holds it securely. The seal is provided by a corrosion-resistant gasket sandwiched between the shut-off collar and the mounting flange.